Honda Civic/Acura Integra

since 1994 release

Repair and operation of the car



Honda Tsivik
+ Cars of the Honda Civic and Acura Integra brand
+ Maintenance instruction
+ Routine maintenance
+ Engine
- Cooling system and heating
   Specifications
   Antifreeze - general information
   Check of serviceability of functioning and replacement of the thermostat
   Check of a condition of the fan(s) of the cooling system and chain of its inclusion, replacement of the fan(s)
   Removal and installation of a radiator and broad tank of the cooling system
   Removal and installation of the oil cooler
   Check of a condition of the water pump
   Replacement of the water pump
   Check of serviceability of functioning and replacement of the block of the sensor of the measuring instrument of temperature of cooling liquid
   Check of serviceability of functioning of a driving electric motor of the fan of a heater and condition of components of its electric chain, replacement of components
   Removal and installation of an electric motor of the drive of the fan of a heater
   Removal and installation of assembly of the control panel of functioning of a heater and conditioner of air, adjustment of a driving cable
   Replacement of the heat exchanger of a heater
   Check of serviceability of functioning and service of systems of heating and air conditioning
   Check of an electric chain of a clutch coupling of the K/V compressor
   Removal and installation of a receiver dehumidifier To/in
   Removal and installation of the K/V compressor
   Removal and installation of the K/V condenser
   Removal and installation of the K/V evaporator with the broad valve
+ Power supply system and release
+ Engine electric equipment
+ Control systems of the engine
+ Gear shifting box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment




Check of serviceability of functioning and replacement of the thermostat

Do not open a cover of a radiator and do not remove the thermostat before full cooling of the engine! See also prevention at the beginning Antifreeze - general information.

Check

 PERFORMANCE ORDER

1. Before finally being approved in a thermostat exit out of operation, check the level of cooling liquid in system, a state and effort of a tension of a driving belt (see the Head Routine maintenance), and also serviceability of functioning of the measuring instrument of temperature.
2. One of possible the reason of too slow warming up of the engine (according to indications of the measuring instrument jamming of the thermostat in open situation is. Replace the thermostat new.
3. In case of an overheat of the engine touch the top hose of a radiator. If the hose is not heated, perhaps, the thermostat is jammed in a closed position, blocking circulation of cooling liquid through a radiator. Replace the thermostat.

Do not operate the car with the removed thermostat at all! At the same time feedback of the onboard processor can be broken that will lead to increase in toxicity of the fulfilled gases and increase in fuel consumption.


4. If the top hose is heated, it means that cooling liquid circulates through a radiator, i.e. the thermostat is open. Address the materials Diagnostics of Malfunctions of Knots and Systems of the Car.

Replacement

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!


2. Merge cooling liquid from a radiator (see the Head Routine maintenance). If replacement of mix was made recently, keep it for further use.
3. Walk on the top radiator hose to the engine and find a thermostat casing cover.
4. Weaken a collar and remove a hose from the connecting branch pipe. If the hose "stuck", grasp it with nippers (as it is possible closer to the end) and try to rotate on a branch pipe for the purpose of destruction of the holding layer. the old, subject to replacement hose can just be cut (try not to scratch a branch pipe).
5. If the surface of a branch pipe contacting to a hose is struck with corrosion, or mechanically damaged, it makes sense to replace a thermostat casing cover.

6a. Disunite the electric socket of the sensor of temperature of cooling liquid of the engine (EST), turn out fixing bolts and uncover a casing of the thermostat (Honda Civic). If the cover "stuck", tap it the hammer with soft brisk. Prepare for collecting the spilled liquid.

6b. Arrangement of bolts of fastening (Acura Integra).

7. Try to remember adjusting position of the thermostat (a finger up), then take it from a casing.

8. Replace rubber sealing laying of the thermostat (see an accompanying illustration).

9. Install the thermostat in a casing (do not apply any sealant). Track that it was developed by a finger up, and the party equipped with a spring to the engine (see an accompanying illustration).

10. Establish into place a cover and fix it by bolts, having tightened the last with the required effort.
11. Connect a hose to a cover branch pipe and strongly fix it by a collar. Return into place all components which were removed for the purpose of ensuring access.
12. Fill in in system necessary amount of cooling liquid (see the Head Routine maintenance).
13. Start the engine and check it for existence of leaks and serviceability of functioning of the thermostat (see paragraphs with 2 on 4).