Honda Civic/Acura Integra

since 1994 release

Repair and operation of the car



Honda Tsivik
+ Cars of the Honda Civic and Acura Integra brand
+ Maintenance instruction
+ Routine maintenance
+ Engine
+ Cooling system and heating
+ Power supply system and release
+ Engine electric equipment
+ Control systems of the engine
+ Gear shifting box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   Specifications
   Care of components of a body and bottom of the car
   Care of vinyl elements of finishing
   Care of an upholstery and carpets of salon
   Repair of insignificant damages of body panels
   Repair of seriously damaged body panels
   Service of loops and locks of the car
   Replacement wind and other fixed glasses
   Removal, installation and adjustment of provision of a cowl
   Removal and installation of a latch of the lock of a cowl and cable of its drive
   Removal and installation of assemblies of forward and back bumpers
   Removal and installation of forward wings
   Removal and installation of a latch, cylinder of the lock and emphasis of a door of a back
   Removal, installation and adjustment of a door of a back
   Removal and installation of a latch, cylinder of the lock and emphasis of a cover of the luggage compartment
   Removal, installation and adjustment of a cover of the luggage compartment
   Driving cables of an otpuskaniye of locks of covers of the luggage compartment and hatch of a jellied mouth of the fuel tank
   Removal and installation of an internal upholstery of doors
   Removal, installation and adjustment of provision of doors
   Removal and installation of latches and cylinders of locks and external and internal handles of doors
   Removal and installation of door glasses
   Removal and installation of the regulator of a window regulator
   Removal and installation of rear-view mirrors
   Removal and installation of the central console
   Removal and installation of the dashboard
   Removal and installation of a casing of a steering column
   Removal and installation of an instrument guard
   Removal and installation of a forward fairing
   Removal and installation of seats
   + Control body sizes
+ Onboard electric equipment


http://flashlottos24.ru/



Removal and installation of a latch of the lock of a cowl and cable of its drive

Considered in the present manual of the car are equipped with safety cushions (SRS). When performing any works near sensors of blows, a steering column or the dashboard disconnect SRS (see schemes of electric connections at the end of the Head Onboard electric equipment).

Latch

 PERFORMANCE ORDER

1. Remove a folding cover of a decorative front grille, then lead round assembly of a latch a marker or a chertilka for the purpose of a guarantee of correctness of its installation at assembly. Turn out fixing bolts from the radiator support panel and remove a latch (see an illustration).

2. Disconnect a lock otpuskaniye cable from assembly of a latch.
3. Installation is made upside-down.

Adjust the provision of a latch so that the cowl was reliably fixed by the lock in a closed position – rubber pillows of support have to be flattened slightly.

Driving cable

 PERFORMANCE ORDER

1. Disconnect a driving cable of an otpuskaniye of the lock of a cowl from assembly of a latch (see an accompanying illustration).

2. In interior of the car remove the top overlay of a threshold of a driver's door, then give two fixing bolts and disconnect separate from a partition the cowl lock otpuskaniye lever (see an accompanying illustration). Disconnect a driving cable from the lever.

3. Tie up a piece of a rigid wire by the end of a cable connected to a latch, then "walk" on a cable to a back partition of a motive compartment, on the way releasing it from intermediate clamps.
4. Push the rubber plug through passage through a partition and involve a cable in a motive compartment of the car. Make sure that assembly of a new cable is equipped with the plug through passage. Untie an old cable from a wire and tie up instead of it replaceable.
5. Involve assembly of a new cable for a wire through a partition in a motive compartment.
6. You make further assembly as it should be, the return to a dismantle order.

Fingers densely push the plug of a cable through passage into a partition of a motive compartment – track correctness of landing of the plug in a partition.