Honda Civic/Acura Integra

since 1994 release

Repair and operation of the car



Honda Tsivik
+ Cars of the Honda Civic and Acura Integra brand
+ Maintenance instruction
+ Routine maintenance
- Engine
   - Repair of the engine without extraction from the car - the Civic model
      General information
      Preparatory actions and the list of repair procedures which can be executed without extraction of the engine from the car
      Reduction of the piston of the first cylinder in the provision of the top dead point (TDP)
      Removal and installation of a cover of a head of cylinders
      Removal and installation of the inlet pipeline
      Removal and installation of a final collector
      The VTEC systems - the general information and check of a condition of components
      Removal, check of a state and installation of assembly of yokes
      Replacement of valvate springs with plates and maslootrazhatelny caps
      Removal, check of a state and installation of a gas-distributing belt and cogwheels of the GRM drive
      Replacement of a forward epiploon of a bent shaft
      Removal, check of a state and installation of the camshaft
      Removal and installation of a head of cylinders
      Removal and installation of the pallet of a case of the engine
      Removal, check of a state and installation of the oil pump
      Removal and installation of a flywheel / driving disk
      Replacement of a back epiploon of a bent shaft
      Check of a state and replacement of support of a suspension bracket of the power unit
   + Repair of the engine without extraction from the car - the Integra model
   + General and capital repairs of the engine
+ Cooling system and heating
+ Power supply system and release
+ Engine electric equipment
+ Control systems of the engine
+ Gear shifting box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment




Removal and installation of the inlet pipeline

It is worth to remember that gasoline is flammable liquid in the highest measure, – during the work with components of a power supply system observe all taken measures of fire safety. You do not smoke and do not approach the venue of works with naked flame or the carrying unprotected by the lamp shade. You do not make service of system in the room equipped with the heating devices using natural gas and equipped with a control torch (such as vodogre and dryers for clothes). Do not forget that gasoline is among the cancerogenic substances promoting development of cancer – try not to allow hits of fuel on open parts of the body – use protective rubber gloves, at casual unforeseen contact carefully wash out hands warm water with soap. Immediately collect the spilled fuel and do not put the rags impregnated with fuel and lubricants near sources of naked flame. Remember that the power supply system of the models equipped with injection of fuel constantly is under pressure. Before starting a detachment of fuel lines, dump residual pressure in system (for more details see the Head of the Power supply system and release). At service of components of a power supply system put on goggles. Constantly hold near at hand the class B fire extinguisher!

Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!


2. Empty the cooling system (see the Head Routine maintenance).
3. Remove the air cleaner with an air inlet (see the Head of the Power supply system and release).

4. Having accurately marked, disconnect everything the electrical wirings and vacuum lines preventing dismantle of the inlet pipeline (see an accompanying illustration).

5. Disconnect an accelerator cable from the lever of the drive of a butterfly valve (see the Head of the Power supply system and release).
6. Remove hoses of a cooling path from the throttle case.
7. Dump pressure in a power supply system and disconnect from the fuel highway of the line of giving and return of fuel (see the Head of the Power supply system and release).

8. Working from below under a motive compartment, remove the assembly bracket supporting the inlet pipeline (see an accompanying illustration).

9. Disconnect from the inlet pipeline perepuskny a cooling system hose (see an accompanying illustration).


10. Turn out fixing bolts (see an accompanying illustration) and remove the inlet pipeline from the engine.

Installation

 PERFORMANCE ORDER

1. Wipe with solvent of a nut of fastening of the inlet pipeline, then carefully dry them (whenever possible with use of compressed air).
2. Estimate planeness of the interfaced surface of the pipeline by means of the special measuring instrument (the steel ruler put on an edge) and the probe of lezviyny type.
3. Examine the pipeline on existence of cracks and signs of deformation. The defective pipeline is subject to a pro-point, or replacement.
4. Check a condition of fixture (bolts/hairpins) of the pipeline. Replace defective units.
5. Scratch out traces of material of old laying from the interfaced surfaces of a head and the inlet pipeline, then wipe surfaces with the rags moistened in acetone.

6. Having picked up new sealing laying, install the pipeline on the regular place and fix it, having tightened by hand all nuts. Working in that order (see an accompanying illustration), tighten fixture with the required effort (see Specifications).


7. Further installation is made as it should be, the return to a dismantle order. In conclusion do not forget to fill the cooling system (see the Head Routine maintenance).