Honda Civic/Acura Integra
since 1994 release
Repair and operation of the car
+ Cars of the Honda Civic and Acura Integra brand
+ Maintenance instruction
+ Routine maintenance
+ Repair of the engine without extraction from the car - the Civic model
- Repair of the engine without extraction from the car - the Integra model
Preparatory actions and the list of repair procedures which can be executed without extraction of the engine from the car
Reduction of the piston of the first cylinder in the provision of the top dead point (TDP)
Removal and installation of a cover of a head of cylinders
Removal and installation of the inlet pipeline
Removal and installation of a final collector
Removal, check of a state and installation of a gas-distributing belt and cogwheels of the GRM drive
Replacement of a forward epiploon of a bent shaft
The VTEC systems - the general information and check of a condition of components
Removal, check of a state and installation of camshafts and assembly of yokes
Replacement of valvate springs with plates and maslootrazhatelny caps
Removal and installation of a head of cylinders
Removal and installation of the pallet of a case of the engine
Removal, check of a state and installation of the oil pump
Replacement of a flywheel / driving disk
Replacement of a back epiploon of a bent shaft
Check of a state and replacement of support of a suspension bracket of the power unit
+ General and capital repairs of the engine
+ Cooling system and heating
+ Power supply system and release
+ Engine electric equipment
+ Control systems of the engine
+ Gear shifting box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Onboard electric equipment
Статья взята с сайта krac0tka.ru Источник: https://novostir.ru
Repair of the engine without extraction from the car – the Integra model
This Part of the Head Dvigatel is devoted to the repair of the 4-cylinder petrol engine of 1.8 l equipped with system of injection of fuel which is not connected with extraction from the car (in situ). All procedures demanding dismantle of the power unit are provided in the Part the General and capital repairs of the engine of the present Chapter.
Three versions of engines are applied to a complete set of the considered Acura Integra models. All versions are among engines with two camshafts of the top arrangement (DOHC). About 4 valves (16V) are the share of each of cylinders.
Engines are completed with one of two versions of electronic system of correction of phases of gas distribution (VTEC). To more detailed description of a design and the principle of functioning of the VTEC systems it is devoted the VTEC Systems - the general information and check of a condition of components.
The used engines have the following designations:
The description of the most part of the considered procedures is made on the basis of the assumption that the power unit remains on the regular place in a motive compartment of the car. In view of told in case the engine is already dismantled and installed on a workbench or the assembly stand, many of the described steps have to be lowered.
The engine has a compact design which main component is the block of cylinders manufactured of light aluminum alloy. Steel sleeves of cylinders are inserted into the openings pierced in the block. From above on the block the aluminum head of cylinders is established. The bent shaft is placed in an integral bed with the replaceable inserts of radical bearings put in it. The fourth bearing is equipped with the separate persistent inserts limiting an axial side play of a shaft.
Pistons are equipped two compression and one oil scraper with rings. The piston fingers having semi-floating landing are pressed in the top heads of rods. In the lower heads replaceable inserts of conrod bearings are located.
The engine has liquid cooling on the basis of the centrifugal rotor water pump put in action from a gas-distributing belt. Cooling liquid circulates on internal galleries of the engine, washing cylinders and combustion chambers, and also is banished on the channels equipped in the inlet pipeline.
Supply of lubricant to internal components of the engine is carried out by the gear oil pump located in a forward part of the engine under a cover of a gas-distributing belt. The drive of the pump is carried out directly from a bent shaft. Oil is sucked in via the mesh filter from the case pallet, then banished via the full-line filter of cartridge type installed on the side of the power unit turned to a back partition of a motive compartment.