Honda Civic/Acura Integra

since 1994 release

Repair and operation of the car



Honda Tsivik
+ Cars of the Honda Civic and Acura Integra brand
+ Maintenance instruction
+ Routine maintenance
+ Engine
+ Cooling system and heating
+ Power supply system and release
+ Engine electric equipment
- Control systems of the engine
   Specifications
   System of onboard diagnostics (OBD) - the principle of functioning and codes of malfunctions
   Removal and PCM/ECM installation
   Check of serviceability of a state and replacement of the sensor of provision of a butterfly valve (TPS)
   Check of serviceability of a state and replacement of the sensor of absolute pressure in the pipeline (MAR)
   Check of serviceability of a state and replacement of the sensor of temperature of the soaked-up air (IAT)
   Check of serviceability of a state and replacement of the sensor of temperature of cooling liquid of the engine (EST)
   Check of serviceability of a state and replacement of the sensor of VMT/provision of a cranked shaft / situation of pistons in cylinders of the engine (TDC/CKP/CYP)
   Check of serviceability of a state and replacement of the sensor of fluctuations of a bent shaft (CKF)
   Check of serviceability of a state and replacement of the detector of control of electric loadings (ELD)
   Check of serviceability of a state and replacement of the sensor switch of pressure in system of hydrostrengthening of a wheel (PSP)
   Check of serviceability of a state and replacement of the oxygen sensor (l-probe)
   Check of serviceability of a state and replacement of the sensor of a detonation
   Check of serviceability of a state and replacement of the sensor of speed of the movement of the car (VSS)
   System of stabilization of turns of idling - the general information, check of a state and replacement of the IAC valve
   Check of serviceability of a state and replacement of the thermosensitive valve of turns of bystry idling (FIT)
   System of a perepuskaniye of the soaked-up air - the general information, check of a state and replacement of a diaphragm of the IAB valve
   System of the operated ventilation of a case (PCV)
   System of recirculation of the fulfilled gases (EGR) - the general information, check of a state and replacement of components
   System of catching of fuel evaporations (EVAP) - the general information, check of a state and replacement of components
   The catalytic converter - the general information, check of a state and replacement
+ Gear shifting box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment




Check of serviceability of a state and replacement of the sensor of VMT/provision of a cranked shaft / situation of pistons in cylinders of the engine (TDC/CKP/CYP)

On the considered models the sensor of provision of a bent shaft structurally consists of three parts tracing, respectively, actually the provision of a shaft, the provision of VMT of the engine (TDC sensor) and position of the piston of the cylinder No. 1 (CYP sensor). On the basis of the data arriving from the sensor of ICR, ECM/PCM defines the moments of injection of fuel and ignition in each of engine cylinders, in parallel the sensor delivers information on the frequency of rotation of the engine on the module of management. The correct installation of a corner of an advancing of ignition at start of the engine is determined by signals of the TDC sensor. The CYP sensor informs the module of management on readiness of each of cylinders for injection of fuel in it. All three sensors are united in uniform assembly which is established in the ignition distributor. Diagnostics of malfunctions of sensors is made by means of the reader of data of memory of ECM/PCM (see System of onboard diagnostics (OBD) - the principle of functioning and codes of malfunctions) and measurements of resistance between the corresponding plugs of the socket of an electrical wiring of assembly.

SKRB sensor

 PERFORMANCE ORDER

1. For check of the sensor of ICR disunite the electric socket on the distributor of ignition and measure resistance between plugs 2 and 6 in it (see an accompanying illustration). Compare result of measurement to requirements of Specifications.

2. Check plugs 2 and 6 for existence of conductivity on weight – conductivity SHOULD NOT be, otherwise replace assembly of the distributor (see the Head Elektrooborudovaniye of the engine).
3. If it is not possible to reveal causes of infringement, drive away the car on car repair shop for more detailed diagnostics.

TDC sensor

 PERFORMANCE ORDER

1. For check of the sensor disunite the electric socket on the distributor of ignition and measure resistance between plugs 3 and 7 in it (see an illustration above). Compare results of measurement to requirements of Specifications.
2. Check plugs 3 and 7 for existence of conductivity on weight – conductivity SHOULD NOT be, otherwise replace assembly of the distributor (see the Head Elektrooborudovaniye of the engine).
3. If it is not possible to reveal causes of infringement, drive away the car on car repair shop for more detailed diagnostics.

CYP sensor

 PERFORMANCE ORDER

1. For check of the sensor disunite the electric socket on the distributor of ignition and measure resistance between plugs 4 and 8 in it (see an illustration above). Compare results of measurement to requirements of Specifications.
2. Check plugs 4 and 8 for existence of conductivity on weight – conductivity SHOULD NOT be, otherwise replace assembly of the distributor (see the Head Elektrooborudovaniye of the engine).
3. If it is not possible to reveal causes of infringement, drive away the car on car repair shop for more detailed diagnostics.