Honda Civic/Acura Integra

since 1994 release

Repair and operation of the car



Honda Tsivik
+ Cars of the Honda Civic and Acura Integra brand
+ Maintenance instruction
+ Routine maintenance
+ Engine
+ Cooling system and heating
+ Power supply system and release
+ Engine electric equipment
+ Control systems of the engine
+ Gear shifting box
+ Coupling and power shafts
+ Brake system
- Suspension bracket and steering
   Specifications
   Removal and installation of assembly of the forward shock-absorber with a screw spring
   Replacement of the shock-absorber or screw spring of rack-mount assembly of a forward suspension bracket
   Removal and installation of the forward stabilizer of cross stability with basic plugs
   Removal and installation of the top control lever of a forward suspension bracket
   Removal and installation of the lower control lever of a forward suspension bracket
   Removal and installation of a rotary fist and stupichny assembly
   Removal and installation of assembly of a forward nave with the wheel bearing
   Replacement of spherical support
   Removal and installation of assembly of the back shock-absorber with a screw spring
   Removal and installation of a bar of the back stabilizer of cross stability with basic plugs
   Removal and installation of assembly of a back nave with the wheel bearing
   Removal and installation of levers of a back suspension bracket
   Removal and installation of a steering wheel
   Removal and installation of tips of steering drafts
   Replacement of protective covers of the steering mechanism
   Removal and installation of the steering mechanism
   Removal and installation of the steering pump
   Removal of air from a hydraulic path of system of strengthening of a wheel
   Wheels and tires - the general information
   Angles of installation of wheels
+ Body
+ Onboard electric equipment


http://flashlottos24.ru/



Removal and installation of a rotary fist and stupichny assembly

Removal

 PERFORMANCE ORDER

1. Take off a rim cap. Weaken a stupichny nut (see an accompanying illustration). Weaken nuts of fastening of a wheel, then a front of the car and establish to a poddomkratta it on props. Remove a wheel. Turn off a stupichny nut.

2. Release a flexible brake hose from an arm on assembly of a rotary fist. Otboltite a support of the brake mechanism also tie up it a wire to a screw spring. Remove also anchor bracket of a support and a brake disk (see the Head the Brake system).
3. Disconnect from a rotary fist a tip of steering draft (see Removal and installation of tips of steering drafts).
4. Separate the lower lever of a suspension bracket from a spherical support in the lower part of a rotary fist (see Removal and installation of the lower control lever of a forward suspension bracket).
5. Separate the top end of a fist from a spherical support of the top lever of a suspension bracket.
6. Accurately delay assembly of a fist with a nave outside, having removed it from a pin of a power shaft. In case of need knock on a pin end face with the hammer with soft brisk for the purpose of its release from a nave. Tie up assembly of a power shaft a wire in order to avoid damage of the internal CV JOINT.

Installation

 PERFORMANCE ORDER

1. Slightly grease with special lubricant of a vent of an external pin of a power shaft. Pass a pin through an opening in a nave, at the same time filling a rotary fist on the regular place.
2. Connect the top part of a fist to a spherical support of the top lever of a suspension bracket (see Removal and installation of the top control lever of a forward suspension bracket). Tighten a nut of a spherical finger with the required effort.
3. Connect a spherical support in the lower part of a fist to the lower lever of a suspension bracket (see Removal and installation of the lower control lever of a forward suspension bracket).
4. Establish into place a brake disk, an anchor bracket and a support (see the Head the Brake system).
5. Screw a stupichny nut on a pin of a power shaft and strongly tighten it.
6. Establish a wheel, lower the car on the earth and tighten wheel nuts with the required effort (see Specifications to the Head Routine maintenance).
7. Tighten a stupichny nut with the required effort.