Honda Civic/Acura Integra

since 1994 release

Repair and operation of the car



Honda Tsivik
+ Cars of the Honda Civic and Acura Integra brand
+ Maintenance instruction
+ Routine maintenance
+ Engine
+ Cooling system and heating
+ Power supply system and release
+ Engine electric equipment
+ Control systems of the engine
+ Gear shifting box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
- Onboard electric equipment
   General information and precautionary measures
   Search of causes of failures of electric equipment
   Safety locks - the general information
   Chain breakers
   The relay - the general information and check of serviceability of functioning
   Check of serviceability of functioning and replacement of the breaker of indexes of turns / alarm system
   Check of serviceability of functioning and replacement of understeering switches
   Check of serviceability of functioning and replacement of the switch of ignition and lock of blocking of a steering column
   Check of serviceability of functioning and replacement of switches of the dashboard
   Check of serviceability of functioning of measuring instruments of a combination of devices
   Removal and installation of a combination of devices
   Removal and installation of the radio receiver and loudspeakers
   Removal and installation of the antenna of the radio receiver
   Replacement of lamps of head headlights
   Adjustment of the direction of optical axes of head headlights
   Replacement of block headlights
   Replacement of lamps
   Running fires of daylight (DRL)
   Check of serviceability of functioning and replacement of an electric motor of the drive of screen wipers
   Check of serviceability of functioning and replacement of a horn of a horn
   Check of serviceability of functioning and recovery repair of a heater of back glass
   Control system of speed (темпостат) - general information and check of serviceability of functioning
   The electric drive of window regulators - general information and check of serviceability of functioning
   The uniform lock - general information and check of serviceability of functioning
   The electric drive of external rear-view mirrors - general information and check of serviceability of functioning
   Safety cushions - the general information
   + Schemes of electric connections - the general information




Safety cushions – the general information

General information

All models considered in the present manual are equipped with system of additional safety (SRS) better known under the name of safety cushions. The obligatory complete set included two safety cushions. The system provides additional protection of the driver and forward passenger of the car at strong front blow.

The system consists of the SRS block with switched on in it by the sensor of the directed overloads, the control sensor, a contour of self-diagnostics and a contour of feedback. The block is located under the dashboard, directly ahead of the central console. Modules of safety cushions are built in in the central part of a steering wheel and the right part of the dashboard of the car (directly over a ware box).

Principle of functioning

Necessary condition of activation of safety cushions is operation of the sensor of the directed overloads and the control sensor. Operation of sensors leads to short circuit of a chain of modules and instant filling of pillows with gas. In case of failure of the battery operation of pillows happens due to the energy developed by the feedback knot which is built in in the SRS block.

System of self-diagnostics of refusals of SRS

The system of self-diagnostics of SRS makes inclusion of a control lamp on an instrument guard of the car at turn of the ignition key in position of ON. If the system does not find any deviations, the lamp has to go out about 6 seconds later. If shutdown of a control lamp does not happen, or the lamp works during the movement of the car, therefore, in the SRS system malfunction is found. For check of system and elimination of a cause of failure the car should be driven away on car repair shop.

Service of the knots located near the SRS components

In case of need removals of a steering wheel, or carrying out service of the radio receiver or another, located near the dashboard components try not to allow rassoyedineniye of electric sockets of a chain of SRS. Do not connect any diagnostic equipment to SRS chain at all. AT SERVICE of the SAFETY CUSHIONS of ALL COMPONENTS LOCATED CLOSE ALWAYS PREVIOUSLY DISCONNECT SRS (see below).

Shutdown of the SRS system

The SRS system has to be disconnected every time at performing procedures of service of the safety cushions of components located close!


 PERFORMANCE ORDER

1. Disconnect from the battery at first a negative wire, then positive.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

2. Connect plugs crossing points (red color) to sockets of safety cushions (see below).

Driver's safety cushion

 PERFORMANCE ORDER

1. Uncover access, located under the safety cushion module, then remove red color the plug crossing point (see an accompanying illustration).

2. Disunite the 2-contact socket installed between the module of a safety cushion and the cable reel.
3. Enter the plug crossing point into the 3-contact socket from a safety cushion.

Passenger safety cushion

 PERFORMANCE ORDER

1. Remove a ware box (see the Head Kuzov).

2. Disunite the electric socket located between the module of a passenger safety cushion and the main plait of an electrical wiring of SRS. Enter the plug crossing point into the socket from a pillow (see an accompanying illustration).

Activation of the SRS system

 PERFORMANCE ORDER

1. To put into operation the SRS system after its shutdown (for the purpose of performing procedures of service of any components), take red plugs crossing points from sockets, then restore initial connection of an electrical wiring (to the cable reel and the main plait of SRS) install plugs crossing points in the holders and return into place an access cover / a ware box.
2. Switch off ignition.
3. Connect the battery (at first a positive wire, then negative).

Removal and installation of modules of safety cushions

 PERFORMANCE ORDER

1. Disconnect the SRS system (see above).
2. The description of the procedure of removal of the module of a driver's safety cushion is provided in the Head Podvesk and steering.

3. For removal of a passenger safety cushion turn out two fixing screws (see an accompanying illustration).

4. Installation is made upside-down. Do not forget to make activation of system (see above).