Honda Civic/Acura Integra

since 1994 release

Repair and operation of the car



Honda Tsivik
+ Cars of the Honda Civic and Acura Integra brand
+ Maintenance instruction
+ Routine maintenance
+ Engine
+ Cooling system and heating
+ Power supply system and release
+ Engine electric equipment
+ Control systems of the engine
+ Gear shifting box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
- Onboard electric equipment
   General information and precautionary measures
   Search of causes of failures of electric equipment
   Safety locks - the general information
   Chain breakers
   The relay - the general information and check of serviceability of functioning
   Check of serviceability of functioning and replacement of the breaker of indexes of turns / alarm system
   Check of serviceability of functioning and replacement of understeering switches
   Check of serviceability of functioning and replacement of the switch of ignition and lock of blocking of a steering column
   Check of serviceability of functioning and replacement of switches of the dashboard
   Check of serviceability of functioning of measuring instruments of a combination of devices
   Removal and installation of a combination of devices
   Removal and installation of the radio receiver and loudspeakers
   Removal and installation of the antenna of the radio receiver
   Replacement of lamps of head headlights
   Adjustment of the direction of optical axes of head headlights
   Replacement of block headlights
   Replacement of lamps
   Running fires of daylight (DRL)
   Check of serviceability of functioning and replacement of an electric motor of the drive of screen wipers
   Check of serviceability of functioning and replacement of a horn of a horn
   Check of serviceability of functioning and recovery repair of a heater of back glass
   Control system of speed (темпостат) - general information and check of serviceability of functioning
   The electric drive of window regulators - general information and check of serviceability of functioning
   The uniform lock - general information and check of serviceability of functioning
   The electric drive of external rear-view mirrors - general information and check of serviceability of functioning
   Safety cushions - the general information
   + Schemes of electric connections - the general information




Check of serviceability of functioning and replacement of the switch of ignition and lock of blocking of a steering column

Considered in the present manual of the car are equipped with safety cushions (SRS). When performing any works near sensors of blows, a steering column or the dashboard disconnect SRS (see Safety cushions - the general information). You do not make check of the SRS models by means of any type of the diagnostic equipment.

Ignition switch

 PERFORMANCE ORDER

1. Disconnect from the battery at first a negative wire, then positive.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!


2. Remove the lower section of the dashboard and casings of a steering column (see the Head Kuzov).

3. Moving on a switch electrical wiring plait along a steering column to the assembly block down, disunite electric sockets (see accompanying illustrations).

4. Check existence of conductivity between switch plugs (see the table below).
5. At identification of violations in distribution of conductivity replace the switch.
6. Insert a key into the lock and turn it in position of LOCK (Blocking).

7. Turn out two fixing screws and remove the switch from a steering column (see an accompanying illustration).

8. Installation is made upside-down.

Card of conditions of the switch of ignition

POSITION OF THE SWITCH

EXISTENCE OF CONDUCTIVITY BETWEEN PLUGS

Parking situation (ASS)

   Civic

3 and 8

   Integra

3 and 11

Incl. (ON)

   Civic

3, 8, 10 and 12

   Integra

3, 8, 9 and 11

Start (START)

   Civic

1, 3 and 12

   Integra

1, 3 and 8

Cylinder and assembly of the lock of blocking of a steering column

 PERFORMANCE ORDER

1. Turning the cylinder in everything from the provided provisions, estimate degree of its wear in side play size. The provision of a key in the lock has to correspond to the marking put on the case of assembly. In case of malfunction of the cylinder all castle assembly is subject to replacement.
2. Disconnect from the battery at first a negative wire, then positive.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!


3. Remove a casing of a steering column and the lower section of the dashboard (see the Head Kuzov).
4. Remove the ignition switch (see above).
5. Give fixing nuts and lower a steering column.

6. Assembly of the lock is fixed in a column by a collar, attracted by two screws with srezny heads (see an accompanying illustration). Nakernite of a head of screws, then drill them (use a drill on 4.8 mm). Throw off a collar and remove assembly of the lock from a steering column.

7. Without inserting a key, put the replaceable lock on the regular place and fix it by bolts with nuts. Tighten nuts of fastening of a steering column to a dashboard flange with effort of 12.2 Nanometers. Coupling bolts of the fixing plug drag on with effort of 22 Nanometers.
8. Install into place the ignition switch, and also sections of the dashboard and a casing of a steering column.
9. Connect to the battery at first a positive wire, then negative.