Honda Civic/Acura Integra

since 1994 release

Repair and operation of the car



Honda Tsivik
+ Cars of the Honda Civic and Acura Integra brand
+ Maintenance instruction
+ Routine maintenance
- Engine
   + Repair of the engine without extraction from the car - the Civic model
   + Repair of the engine without extraction from the car - the Integra model
   - General and capital repairs of the engine
      General information
      Check of pressure of oil
      Check of compression pressure in cylinders
      Diagnostics of a condition of the engine with use of the vacuum gage
      Removal from the car of the power unit - preparation and precautionary measures
      Removal and installation of the engine
      Alternative versions of schemes of recovery repair of the engine
      Order of dismantling of the engine by preparation it to capital repairs
      Dismantling of a head of cylinders
      Cleaning and check of a condition of a head of cylinders
      Service of valves
      Assembly of a head of cylinders
      Removal of conrod and piston assemblies
      Removal of a bent shaft
      Cleaning of the block of the engine
      Check of a condition of the block of the engine
      Honingovaniye of mirrors of cylinders
      Check of a condition of components of conrod and piston group
      Check of a condition of a bent shaft
      Check of a state and selection of inserts of radical and conrod bearings of a bent shaft
      Engine assembly order
      Installation of piston rings
      Installation of a bent shaft and check of working gaps of radical bearings
      Replacement of a back epiploon of a bent shaft
      Installation of conrod and piston assemblies and check of size of working gaps in conrod bearings of a bent shaft
      Trial start and running in of the engine after capital repairs
+ Cooling system and heating
+ Power supply system and release
+ Engine electric equipment
+ Control systems of the engine
+ Gear shifting box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment




Removal of a bent shaft

Removal of a bent shaft is possible only from the engine taken from the car. It is meant that a flywheel / a driving disk, a cogwheel of a bent shaft, a gas-distributing belt, the case pallet, a maslozabornik, the oil pump, a maslootrazhatel and (on B18B1 engines) conrod and piston assemblies are already dismantled. Before removal of a bent shaft it is also necessary to otboltit and separate from the block of cylinders the holder of a back epiploon.


 PERFORMANCE ORDER

1. Before starting extraction of a bent shaft from the engine, measure the size of its axial side play. Fix the DTI measuring instrument on the block to coaxially bent shaft, having rested its plunger against a cheek of one of cranks or a pin end face (see an accompanying illustration) the last.


Covers of radical bearings and their connecting bridge have to remain on the places, and their fixture is tightened with the required effort.


2. Push a bent shaft against the stop back and nullify the device indicator. Now push a shaft in an opposite direction and consider the indication of the measuring instrument. The size of a free wheeling of a shaft in the longitudinal direction is also its axial side play. Compare result of measurement to requirements of Specifications. If the side play exceeds the maximum admissible value, check persistent surfaces of a shaft for existence of signs of excessive wear. In the absence of obvious signs of wear, installation of new persistent washers usually helps to correct a situation.

3. In the absence of near at hand dial measuring instrument it is possible to use the ordinary probe of lezviyny type. Accurately shift a shaft against the stop forward on the engine, then determine the size of the formed gap between a cheek of a crank and a forward wall of the persistent (fourth) radical bearing, having densely put in it the corresponding thickness a probe edge(s) (see an accompanying illustration).

4a. Besides serial number on covers marking in the form of cast shooters is usually provided. On correctly established covers of the shooter has to specify in the direction of a belt of the GRM drive. In stages (on 1/4 turns for approach) weaken bolts of fastening of covers of radical bearings and/or their connecting bridge so that the possibility of their reversing manually appeared.

4b. On the Civic models check covers of radical bearings for existence on them adjusting marking. In case of need put marking independently by means of a center punch.

4c. On the Integra models check covers of radical bearings for existence on them adjusting marking. Covers have to be numbered consistently in the direction in front back on the engine (see an accompanying illustration).

5. Uncover radical bearings or assembly of their bridge. On the Integra models accurately tap the remained covers the hammer with soft brisk for the purpose of their separation from the engine block. In case of need use as levers fixing bolts. Try not to drop inserts.
6. Carefully take a bent shaft from the engine (use the help of the assistant). Track that inserts of radical bearings remained in the beds in the block and covers. Install covers on the block, then by hand tighten bolts of their fastening.